Tools

The BKM-1 Hydraulic Brake Bleed Kit will bleed most models of mineral-oil-based hydraulic brakes. Hydraulic systems need bleeding to remove any air bubbles and to inject new, clean fluid. - Designed and built for home use and for the rigors of daily commercial use - Includes two syringes, hoses with shutoff clips, multi-size bleed blocks, bleed funnel and a unique attachable syringe mount - Housed in a rugged reusable case - Machined 7075 aluminum fittings to service Shimano, Magura, Clarks, Promax, Tektro, TRP and other brands of mineral-oil-based hydraulic brake systems - Replacement parts available - Brake fluid not included

With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")

Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.

The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.

With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The Park Tool TW-5.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). With a range of 2-14Nm, the TW-5.2 is designed for the lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.

This professional-grade set includes five unique cleaning tools purpose-built for scrubbing away dirt and grime, with long ergonomic handles for leverage and comfort. The soaping brush, bottle brush and straight brush feature bristles made from tampico, a natural fiber derived from the agave plant. Tampico is extremely durable, resists chemicals, and holds moisture well, making it an ideal material for cleaning brushes. BCB-5 FEATURES Included brushes: - Soaping Brush: Great for making an initial pass over the bike, dispersing soapy water and breaking up large accumulations of debris. - Tapered Bottle Brush: A general purpose tampico brush for scrubbing areas both big and small. - Straight Brush: A long-reach brush with short, tight tampico bristles for getting into small nooks and crannies such as suspension pivots, saddle rails, and other hard to reach areas. - Drivetrain Brush: Long, stiff nylon bristles make this brush ideal for derailleurs, cassettes, and other areas with grease or dirt build up. - Soaping Sponge: Useful for applying soap and water as well as cleaning delicate surfaces, with a convenient wedge shape. Notes about tampico fibers: - Tampico is a natural fiber: as such, variations in the color of the bristles are to be expected. - Tampico bristles may become temporarily deformed in shipment or storage. Get brushes wet, reshape by hand, and hang to dry. - Always allow tampico brushes to dry fully in an open area before storage to inhibit growth of mildew or mold.

A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP). *The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets. - Comfortable T-handle - Replaceable driving pin (CTP) - Investment cast steel body - Adjustable locating shelf

Accurately gauge the straightness of disc brake rotors while the wheel is mounted in a TS-2.2 or TS-2 Professional Wheel Truing Stand (each sold separately). Park Tool's Rotor Truing Gauge features an infinitely adjustable, finely threaded indicator gauge. It works with any diameter brake rotor.

A fast and convenient tool to remove and install 12-spline Shimano/SRAM style cassette lockrings, as well as similar lockrings on rotor discs. The FR-5H features a modified FR-5 tool that allows use without removing most quick release skewer nuts. The removable, threaded steel handle makes it possible to replace a worn or damaged head. - Fits Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and other cassette lockrings - Also fits some Shimano disc brake lockrings

Park Tool's 750.2 Centering Cone Adaptor increases the size of the centering cone of the HTR-1 and HTR-1B Headtube Reaming and Facing Sets. The 750.2 will allow you to use the HTR-1(B) to ream and face head tubes designed to accept IS, ZS, and 1.5-inch EC headset standards. Before reaming or facing, make sure you have the correct cutting tool and pilot for the headset standard(s) you are using. Please refer to our product pages for cutters and pilots for this detailed compatibility information.

A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.

The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.

To prevent poor shifting and uneven drivetrain wear, most manufacturers recommend chain replacement at or before 1% stretch. Now you can quickly and accurately determine the wear and stretch of any chain with Park's Chain Checker. Simply insert the Chain Checker’s pins into 2 links, press the swingarm gauge tight, and then check the gauge window for an accurate reading!

Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent

Made from tough steel and reinforced with extra material at the highly stressed wrench openings, Park’s shop-quality Pedal Wrench is built to easily install and remove pedals, and to last and last. It has 15mm and 9/16-inch precision openings to fit all pedals. And it boasts a long, round, vinyl-coated handle that won’t dig into your hand and provides optimum leverage. There's even a hole in the end of the wrench for hanging it on your toolboard.

Forged and machined, the ZP-5 is ideal for closely cutting zip ties and many other materials in tight spaces.

Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.

The BBT-22 is a shop-quality tool for installing and removing Shimano and ISIS Drive splined 20-tooth bottom bracket cups. Made from investment-cast steel, the BBT-22 ensures maximum engagement with the bottom bracket cup. It can be used with a 3/8-inch drive torque wrench, a 3/8-inch ratchet driver, a 32mm wrench, the Park FRW-1 Freewheel Remover Wrench (sold separately), or a 1-inch wrench.

Park's Home Mechanic Pedal Wrench is great for your home workshop and event tool box. This top-quality 15mm pedal wrench provides the leverage you need to remove stubborn pedals. It's made to last from heat-treated steel, and the handle has a vinyl grip for comfort.

Precision CNC machined aluminum tool for the installation and removal of 16-notch external bearing bottom brackets. Featuring updated tooth profiles to optimize the fit between the tool and high performance BB parts. Anodized and laser engraved for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. - 16-notch 39mm OD cups - Fits: Shimano XTR BB93, Dura-Ace BB9000, Token - Added depth to fit Shimano STEPS square drive motor

The MT-10, 20, 30 and 40 are high quality folding take-along tools that feature forged aluminum side plates, a mix of hardened and plated tools, and smooth ergonomic operation.

Destined to become a classic, the Master Spoke Wrench is an investment cast workhorse poured from the best steel, precisely machined, heat treated for hardness, then polished and plated. The result is a smooth, solid, perfectly balanced steel spoke wrench designed and built to fit perfectly in your hand and provide years of every day service. The SW-20.2 is a three-sided spoke wrench the same size as the SW-0 (black) for .127” (3.23mm) nipples. Weight: 39g

Destined to become a classic, Park Tool's Master Spoke Wrench is an investment cast workhorse poured from the best steel, precisely machined, heat treated for hardness, then polished and plated. The result is a smooth, solid, perfectly balanced steel spoke wrench designed and built to fit perfectly in your hand and provide years of every day service. The SW-22.2 is a three-sided spoke wrench the same size as the SW-2 (red) for .136” (3.45mm) nipples. Weight: 39g

Park Tool's versatile and durable 8oz Shop Hammer is a perfectly balanced striking instrument built for a wide variety of shop uses. - Forged steel, precision machined striking face - Non marring, replaceable composite tip - Fiberglass shaft with soft touch grip - 8oz (225g) Head - Length: 12" (30.5cm) - Steel striking face: 1" (25mm) diameter - Plastic face: 1-1/4" (32mm) diameter - Replacement tip: Part #293-8

Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.

A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.

The Park FR-6 Freewheel Remover fits most 4-notch BMX and singlespeed freewheels. It can be held with a wrench or vise and its narrow profile allows use without removal of cones and locknuts.

Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-4 has 1.7mm tips on bent nose blades for larger, internal snap rings. The tips open from 21mm down to 2mm (center to center).

The TL-6.2 is a composite covered, steel core tire lever that provides smooth, scratch-free operation and superior strength to help remove even the tightest tires. Newly upgraded with a tougher, more slippery material and a protruding steel tip to more easily and securely engage the tire bead. A perfect size (5"/12.7cm) to either take-along, or use as an everyday shop lever. Set of two.

Park Tool's professional-quality Snap Ring Pliers are made from forged, heat-treated cro-moly steel with a return spring and vinyl-dipped grips. The RP-3 has 1.3mm tips on bent nose blades for medium, external snap rings.