Riser

The Next R handlebar features 800mm of premium unidirectional carbon with the shred-ready positioning of Race Face's SixC bars. DH strength and Enduro weight for when you really need to lean into it. - Manufactured from UD Carbon with matte clearcoat - Carbon optimized flex for improved small bump compliance - 35mm bar diameter for incredible strength/weight ratio

Race Face Atlas riser handlebar with an anodized, shot-peened finish. - Aonodized, shot-peened finish - Cold-drawn and butted proprietary AirAlloy aluminum tubing - 4 degree upsweep

Wider than Turbine but still sporting the agressive sweep design putting you in the perfect riding position, these bars come in a variety of rises to allow you to fine tune your cockpit and dial in your setup. Tried and tested 7075 aluminum gives you the confidence for agressive all-mountain riding and 35mm technology for fantastic overall weight/strength ratio. Your six inch travel bike will thank you. - Manufactured from cold drawn, 7075 Aluminium - 35 optimized triple butted design - Turned up to Rally control with 800mm width - Rise sizes to for every build and preference 10/20/35mm - Stealth black on black decals to match every frame color

DEITY Racepoint handlebars must pass DEITY specific impact and stress testing based on the rate of deflection product goes through in real world situations. This is just the beginning, every DEITY handlebar also undergoes a rigorous 12 to 24 month real world testing process under the most abusive riders in the world. Gradient Butting Technology allows DEITY to put material where we need it and not where we don’t, delivering a significantly stronger handlebar at a similar weight to other bars. - Intended use: Enduro and DH

- High-rise, super strong butted, heat treated 2014 aluminum - Sweep: 7° up, 9° back

An ideal handlebar for riding anything from all mountain to downhill, Renthal's FatBar Carbon handlebar combines a blend of strength, stiffness, shock absorption, and weight savings. - Uni-Directional carbon construction - Ride-tuned to provide an ideal combination of stiffness and shock absorption - Increased center section width for fine-tuned flex characteristics - Downhill and twin crown fork compatible - Permanent graphics, set-up grid and cut marks

- Tough 2014 Aluminum Alloy - 9° Rearward / 6° Upward Sweep

Your favorite bars just got bigger, wider, and lighter, Go figure? The magic of 35—believe the hype! Increasing the bar diameter to 35mm allowed Race Face to shave material from the bar resulting in a dramatic reduction in overall weight while retaining the proven stiffness, strength and performance Race Face bars are known for. The ATLAS 35 bar also expands to an 800mm width (Can be trimmed down to 750mm) for hyperspeed control, can you handle it? - Proven design and durability of the Race Face Atlas bar, with increased stiffness and reduced weight of the 35mm bar platform - Requires 35mm bar clamp diameter stem - Full 800mm width that can be trimmed down to a minimum 750mm - 8 degree rearward sweep, 5 degree upward sweep

Mountain bike terrain is bigger and burlier than ever, so why shouldn’t your components be? Our Guide 35.0 Carbon handlebar increases front-end strength and stiffness for more precise handling inputs. The carbon fiber construction keeps weight to a minimum and soaks up trail chatter. Pair these carbon mountain bike handlebars with our Guide Trail 35.0 Stem and carve, drop, pump, and jump your way down the mountain with confidence. - Bar Clamp Diameter: 35.0mm - Color: Carbon - Width: 760/800mm - Rise: 10/20/40mm - Back Sweep (deg): 8 degree - Upsweep: 5 degree - Material: Carbon

The DEITY Highside 35mm handlebar is an homage to style and skill. The DJ/Slopestyle ready Highside 760 handlebar is the perfect reflection of what listening to the athletes can create. This design allows for a stiff, responsive feel that sets the stage to bring your style to life or life to style. - 7075 T73 Gradient butted aluminum - Full bead blast finish for increased durability and fatigue resistance

- DH Race tuned award-winning alloy handlebar design, developed with World Cup professionals - Injected proprietary foam Vibrocore provides vibration damping to reduce arm pump and hand-numbness - Increased strength and stiffness compared to conventional alloy bars - Shot-peening and anodizing enhances fatigue life even further - Adjustable to 740mm Features - Key Technologies: Vibrocore, Dual XGT, CNC Bending, Impact Ends, MGR Super 6 Alloy - Material: MGR Super 6 Alloy - Weight: ±340g (15mm) / ± 350g (30mm) / ±360g (50mm) - Sweep: 4° up x 8° back - Finish: Shot peen anodized, decal logos

Lightweight aluminum construction with a versatile riser bar design.

- Constructed of lightweight 2014 aluminum alloy - 35mm handlebar clamp diameter - Micro-Adjust Laser-Etched set-up markings - 20mm Rise - 9° Sweep - 5° Back-Sweep

An exceptionally strong carbon fiber 35mm riser bar that’s built to descend. The M7 bar is designed for the most aggressive and demanding riders. Carbon fiber is the ideal material for a gravity bar because fiber orientation and bar shape can be controlled independently and developed in unison, resulting in a tuned flex profile that cannot be achieved with aluminum. This bar is tuned to be precise and responsive while absorbing fatigue-inducing chatter and taking the sting out of the biggest hits. The M7 bar features a trail-perfect 8-degree backsweep and 4-degree upsweep for your long-travel 29er, enduro race bike, or downhill machine. - Material: Carbon - Weight: 230g (10mm rise); 240g (25mm rise); 245g (40mm rise) - Bar Width (Max): 800mm - Bar Width (Min): 780mm - Clamp Diameter: 35mm - Backsweep: 8 Degrees - Upsweep: 4 Degrees - Torque Spec: Face Plate: 5.5Nm - Torque Spec: Controls: 5.5Nm

- Butted alloy tube, cold-drawn and shot-peened to increase fatigue resistance - Intended use: XC, Trail and All Mountain - 8 degree rearward sweep, 5 degree upward sweep - Bar Clamp Diameter: 35.0 mm - Material: Aluminum - Weight: 270 g (10mm) - Width: 760 mm

Thomson's Carbon MTB bars are made with three different fiber types for strength, durability and long times in the saddle. The MTB Carbon Trail Handlebar is built for strength with enough flex built in for all day comfort. It’s strong enough for all mountain/trail riding and light enough for racing. The bars are made with three different fiber types with different tensile strength and tensile modulus, including high strength carbon fibers. This helps to allocate stiffness and flex where needed. The bars are molded with an EPS mandrel inside to avoid wrinkles inside the layup during molding. Most other bars are molded over inflated nylon bladders. All carbon fiber material is produced by Toray and uses tailor made nano Epoxy Resin for very high impact resistance. Toray is the main supplier of carbon fiber to Boeing and Airbus. 1.5K woven impact ends help prevent damage to unidirectional fibers from shortening the bar or impact with the ground. With a light weight and precision tolerance clamp sections, it’s the best bar for your Thomson X4 stem. It’s also certified to EN, tested to DIN+. Friction Paste recommended for installation

- Ideal for fitness and comfort cyclists - A great replacement handlebar

- Ideal for fitness and comfort cyclists - A great replacement handlebar

- The Fatbar Lite Carbon 35 is the ultimate light-weight, trail-proof handlebar. - Designed for Trail, Enduro and XC riders and racers, the Fatbar Lite Carbon 35 is the clear market leader in terms of weight, strength, stiffness and most importantly, ‘rid

Do you love to ride your mountain bike? Love boosting big airs, punishing the trails and your gear? You just want parts that can take a beating and won't let you down — the Chester 35 bar is made for you. These bars will last long after your bones, bruises and scrapes heal up and you're ready to tackle that gap jump that has had your number. - Manufactured from cold drawn, seamless 6061 Aluminum - Shot peened for increased fatigue life - 35 optimized triple butted design

ONEUP CARBON BARS. Strong, lightweight & vertically compliant. The goal for the new OneUp Carbon Handlebars was to make the best feeling bar possible, something which would let us ride harder for longer. The solution is our patent pending oval shape which combines the best ride characteristics of 31.8mm and 35mm bar standards into one package. This is the most comfortable bar we’ve ever ridden, period. It's strong, lightweight, minimizes arm pump and vibration and maximize steering response. 35 done right. Almost every other carbon bar on the market copies the simple tapered profile of an Aluminum bar. With carbon you can take advantage of more complex shapes to get a better performing product, so that's what we did. If you actually care about bar compliance, then you don't make a regular 35mm diameter bar. Sure you can try to "optimize" the flex slightly with layup, but geometry is king and you're fighting a losing battle. The OneUp bar profile minimizes the length of the 35 diameter clamping area as this is the stiffest portion of any 35 diameter bar. The 35mm clamp diameter quickly changes to a flattened, oval shape in the transition zone and then to a standard 22.2mm clamp diameter for the control zone. We benchmarked the OneUp bar against the most popular carbon bars on the market as well as foam filled aluminum bars. The results were, on average, a 21% increase in vertical compliance (comfort) coupled with a 28% increase in steering stiffness (responsiveness). These are more than just marginal gains. Until now the 35mm diameter standard has had a bad reputation and rightly so. This is 35 Dia. done right. SPECS - Geometry: 800mm Wide / 35mm Dia. / Sweep 8° Back 5° Up - Weight: 20mm Rise (220g) 35mm Rise (225g) - Max Stem Clamp Width: 65mm - Max Control Torque: 5Nm - Minimum Trim width: 740mm - Colour: Black. Decal kits: Available in Red, Green, Blue, Orange, Purple & White COMPATIBILITY - Grips with only an outer clamp are not compatible with our bar.

A race-proven handlebar, the M9 bar is ENVE's dedicated downhill option. Designed around a 31.8mm clamp diameter and a downhill-focused flex profile, this bar’s celebrated ride feel defined the potential of a DH carbon fiber bar and realigned performance expectations. The M9 bar features 8-degree backsweep and 4-degree upsweep. - Material: Carbon - Weight: 245g (30mm rise); 265g (50mm rise) - Bar Width (Max): 810mm - Bar Width (Min): 780mm - Clamp Diameter: 31.8mm - Backsweep: 8 Degrees - Upsweep: 4 Degrees - Torque Spec: Face Plate: 5.5Nm - Torque Spec: Controls: 5.5Nm

A slightly modified profile gives the RaceFace Aeffect R handlebar the extra boost you’re looking for at high speeds. Built for tearing down your favorite trail...fast. Generous 780mm width to give you the stance and control you need. This is a no-nonsense, set-and-forget bar that is equally at home on your trail bike as it is on an enduro machine. Take your bike to the Rally level without breaking the bank. - Shot-peened to increase fatigue resistance - 35mm bar diameter allows for additional material to be shaved from the handlebar, while retaining stiffness, strength and performance - Manufactured from cold drawn, seamless aluminum - Upsweep: 5° - Backsweep: 9°

Simply put, it's the perfect trail bar. The M6 bar is tuned for the dream combination of response, compliance, and high strength. Available in a traditional 25mm rise or a low 7.5mm rise, it sweeps back at 9 degrees and up 5 degrees, providing excellent support and a classic fit. Designed around a 31.8mm clamping diameter, the carbon laminate is tuned to deliver the ideal flex profile for trail use. This bar provides excellent vibration damping and response, making it the perfect choice for long days on epic terrain. - Material: Carbon Fiber - Weight: 200g (25mm rise); 190g (7mm rise) - Bar Width (Max): 780mm - Bar Width (Min): 740mm - Clamp Diameter: 31.8mm - Sweep: 9 Degrees - Tip: 5 Degrees - Torque Spec: Face Plate: 5.5Nm - Torque Spec: Controls: 5.5Nm

With multiple geometry options to choose from, Wald's Steel Handlebars offer great options for riders looking to accessorize their bike or find a replacement option that feels comfortable. - Made in the USA - Chrome finish - Weight: 526g - Lever Compatability: Mountain 22.2mm